ML53L-60 Albright 12-60V DC Magnetic Latching Contactor Controller
|No stock |
Back ordering available.
Part Number: ML53L-60
Voltage: 12V to 60V DC
Pre-order and back-ordering are available with a 6 to 8 week lead time. Telephone: +44 (0) 1924 823119 or Email us to discuss further requirements.
Utilising the latest CMOS technology and surface mount design, the ML53L-60 features enhanced low voltage operation and lower power consumption together with the ability to drive all the contactor coils in the range between 12 and 60 Volts. These simple modules are an option to allow the operation of Albright’s range of bidirectional single pole magnetic latching contactors from a standard DC supply. An ML is designed to operate one contactor coil only.
The ML53 is a five terminal non-sequential device. It is similar to the ML52 except that in addition to ground it has two separate inputs for set (close) and unset (open) of the contactors. If the set (close) input is powered up it will generate a positive pulse at supply voltage of 0.25 seconds duration, long enough to set any of our magnetic Latch contactor range. Each time this input is actuated it will generate a positive pulse. If the unset (open) input is powered up it will up generate a negative pulse at supply voltage of 0.25 seconds duration, long enough to unset any of our magnetic latch contactor range. Each time this input is actuated it will generate a negative pulse. Powering each input alternatively can set (close) and unset (open) the contactor.
- Length including terminals: 69mm.
- Width: 34mm.
- Height: 19mm.
About the ML Range of Controllers
The operation of a single pole magnetic latching contactor requires a short duration pulse typically 0.25 seconds at the coil supply voltage to set (close) the contactor. Once set (closed) the contactor will remain set, even if there is a power outage. Subsequent pulses of the same polarity will not affect its status.
To unset (open) the contactor a pulse of 0.25 seconds duration is applied at the coil supply voltage. Once unset (open) the contactor will remain unset (open), even if there is a power outage. Subsequent pulses and voltages at the same polarity will not affect its status. To set (close) it again the polarity of the pulse must once again be reversed.
Albright offers the ML range for customers requiring an alternating coil polarity drive unit.
Magnetically Latched Contactors do not fail safe. If there is a power failure, or if the supply to the contactor coil is broken, the contactor contacts will not open or close, i.e. they will not change state. These devices should not therefore be used in applications where the failure of contacts to open or close could result in a hazardous situation for persons or equipment.
|Device Type ||ML53L - Magnetic Latching Contactor Controller |
|Voltage ||12 - 60 Volt dc |
|Initial Power-up sequence time ||10mS ±20% |
|Drive Pulse Length ||0.25S ±20% |
|ML Power Consumption ||Less than 10mA + |
|Maximum switching speed ||1 operation per 10 seconds (0.1Hz) |
|Operating Temperature ||Minus 40 to +85°C |
|Maximum Voltage ||60V |
|Minimum Nominal Voltage ||12V |
|Maximum Drive Current ||4A for 0.25s |
Free UK Mainland Postage and Packaging
Free UK Mainland delivery discount is selectable on your shopping cart page; a £50.00 minimum order value is applicable for the Free Delivery Service, with a variable low Standard Rate shipping charge for smaller consignments.
Despatch methods for Standard and Free UK Delivery Service include light, low-value orders despatched via Royal Mail standard or recorded delivery, with large and high-value orders despatched via UPS and Parcel Force courier services.
International orders and consignments require the exact Card Holder Address (Invoicee) as the first address for payment processing. PO Box addresses are not acceptable as delivery addresses by some couriers.
Export orders will only be accepted when placed online.