| 
Need help? Email us: sales1@arc-components.com

0-441-15 Durite 12V-24Vdc Red-Amber High Intensity Warning Light

0-441-15 Durite 12V-24Vdc Red-Amber High Intensity Warning Light
0-441-15 Durite 12V-24Vdc Red-Amber High Intensity Warning Light
0-441-15 Durite 12V-24Vdc Red-Amber High Intensity Warning Light
£69.27 Excl. VAT
RRP £78.72 Excl. VAT
Initial Savings
£9.45
(£83.12 Inc. VAT)
Earn 69 Loyalty Points
   
Available
Model
0-441-15
Bar Code
5056119139716
Part Number
0-441-15
Brand
Durite
Colour
Red/Amber
Voltage
12V/24V DC
Material
Aluminium/Plastic
Weight
60 g
 

 Durites 3 x 3W red and 3 x 3W amber LED ultra-high intensity flush slimline warning light.

  • 12/24Vdc.
  • 20 programmable flash sequences.
  • CE, ECE R65 Class 1 and SAE Class 1 approved.
  • Protected to IP68.

Additional information

  • Red wire +ve supply
  • Black wire -ve ground
  • White wire alternating flash
  • Yellow wire synchronization and flash pattern

Dimensions

  • Length: 113mm.
  • Width: 28.4mm.
  • Height: 9mm.

Specifications

Type Ultra High Intensity LED Warning Light
Colour Red and Amber
Voltage 12/24Vdc
LEDs 6 x 3W
Fixing 2 bolt holes
Current 0.70 amps at 12 volts
Flash Patterns 20
Base Aluminium
Operating temperature -20C to +50C
Protection IP68
Dimensions L 113mm x W 28.4mm x H 9mm
Compliances CE, ECE R65 Class 1 and SAE Class 1
Weight 0.04Kg

General Warnings (For Translation Purpose)

  Before using this unit please read these instructions carefully. Take special care to follow the warnings and safety suggestions listed below. Copy and keep these instructions for future reference.

Safety Warnings

  1. Proper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures.
  2. If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other vita parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling begins. Also de-burr the holes and remove any metal shards or remnants.
  3. Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a projectile that could cause serious personal injury or death. Refer to your vehicle owner’s manual for the air bag deployment area. The User/Installer assumes full responsibility to determine proper mounting location, based on providing ultimate safety to all passengers inside the vehicle.
  4. Do not attempt to activate or control this device in a hazardous driving situation.
  5. This product contains either strobe light(s), halogen light(s), high intensity LED’s or a combination of these lights. Do not stare directly into these lights. Momentary blindness and/or eye damage could result.
  6. Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens cracking (crazing) and discolouration. Lenses in this condition have significantly reduced effectiveness. Inspect and operate this product regularly to confirm its proper operation and mounting conditions. Do not use a pressure washer to clean this product.
  7. It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or reinstallation of this product.
  8. For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE (-) battery post.

Mounting

  1. Place the unit against the mounting surface.
  2. Mark the areas where the mounting holes are to be drilled. Confirm that no vehicle parts could be damaged by the drilling process.
  3. Using a bit size for a No. 304 metal screw, drill two mounting holes, a 0.5″ diameter. Wire passage hole(s) must also be drilled. Thoroughly de-burr all hole(s).
  4. Pass the wires through the hole(s) in the gasket and through the wire passage hole(s) in the mounting surface. Fix the light head to the mounting surface.

Delivery
 
UK Mainland Postage Offer

Delivery Options Our Free UK Mainland Postage and Packaging Service offers unbeatable value for money. The free UK Standard shipping is automatically applied to your shopping cart page with no additional cost when you reach the £50.00 minimum order value.

 We use Royal Mail Standard or Recorded Delivery for light, low-value orders and we use FedEx, UPS, Parcel Force, and other major courier services for larger and more valuable consignments.

 
International Consignments

 Our international customers will need to provide the exact Card Holder Address (Invoicee) as the first address for payment processing. Please note that PO Box addresses are not acceptable as delivery addresses by some couriers. All export orders must be placed and paid for online. Proforma Bank Transfer IBAN and SWIFT payment methods are available to create online.

Also Bought

Customer Feedback (0)
Leave a Review