| 
Need help? Email us: sales1@arc-components.com

0-204-20 Durite 300A Extra Heavy-duty Slave or Jump Lead Set 2.5M

£80.47 Excl. VAT
RRP £91.44 Excl. VAT
Initial Savings
£10.97
(£96.56 Inc. VAT)
Earn 80 Loyalty Points
   
Available
Model
0-204-20
Bar Code
5056119106329
Part Number
0-204-20
Brand
Durite
Colour
Black/Red
Amperage
300A
Material
Copper/PVC
Weight
3.03 kg
 

 Durite pack of 1 extra heavy duty slave or jump lead set.

  • 2.5M long.
  • 539 strands 0.30mm, 40mm² cable.
  • 300A rated cable.
  • PVC insulated,
  • Fitted with solid copper crocodile clips with copper braid bonded jaws.
  • Pack quantity: 1 set of leads.

Safety Instructions for Jump Starting (For lost copies or translation)

  WARNING: Read these instructions in full before attempting to use the jump leads. Before connecting the jump leads ensure that the following safety measures are adhered to.

  • Batteries give off flammable gases - do not smoke or use naked flames.
  • Ensure that both batteries are of the same nominal voltage. Battery or charging system damage or explosions can result if jump starting is attempted with batteries of differing voltage.
  • Ensure that the two vehicles are not touching each other; sparks and vehicle damage could result if they are.
  • Ensure that the jump leads are in good condition; breaks in the conductor or poor connections make starting difficult and can cause overheating and fire.
  • Ensure that the ignition switches of both vehicles are in the off position and that both hand brakes are applied. If the jump leads are connected whilst the ignition is switched on, sparks and fire may result.
  • Always connect the batteries positive (red, +) to positive (red, +) and negative (black. -) to negative (black, -) irrespective of the vehicles' earth terminations.
  • Ensure that both vehicles are in NEUTRAL (for vehicles with manual transmission) or in PARK (for vehicles with automatic transmission).

Procedure for Connecting Jump Leads

  • Connect the jump leads one at a time.
  • Connect the positive lead (red) first.
  • Always attach each jump lead to the charged/donor battery first.
  • Complete both connections of the first lead before making the first connection with the second lead.
  • If the above procedure is followed correctly, the fourth and final connection made will be the earth connection to the discharge battery. Unlike the other connections which are made to the battery terminal post, this final connection shall be made to a good earth point remote from the discharged battery. A suitable earth point may be in engine mounting, chassis member, engine block or any other unpainted surface remote from the battery and away from fuel and brake lines.
  • Start the engine on the donor vehicle and run it for about 1 minute at a fast tick-over, in sub-zero temperatures this time should be extended to 2 minutes or 3 minutes.
  • With the engine of the donor vehicle still running, attempt to start the vehicle with the discharged battery. If nothing happens, switch off the ignition on both vehicles and re-check all connections.
  • After starting the vehicle with the discharged battery, run this engine at a fast tick-over for several minutes to warm-up and then allow to idle. Do not disconnect the jump leads with the engine of either vehicle running at above idle speed: this can cause damage to the charging circuits and to other electronic equipment.

Procedure for Disconnecting the Leads

  • Detach the clip connected to the earth point on the vehicle that had the discharged battery then disconnect the other end of this lead from the donor battery.
  • Disconnect the second lead first from the vehicle that had the discharged battery and then from the donor vehicle.

Delivery
 
UK Mainland Postage Offer

Delivery Options Our Free UK Mainland Postage and Packaging Service offers unbeatable value for money. The free UK Standard shipping is automatically applied to your shopping cart page with no additional cost when you reach the £50.00 minimum order value.

 We use Royal Mail Standard or Recorded Delivery for light, low-value orders and we use FedEx, UPS, Parcel Force, and other major courier services for larger and more valuable consignments.

 
International Consignments

 Our international customers will need to provide the exact Card Holder Address (Invoicee) as the first address for payment processing. Please note that PO Box addresses are not acceptable as delivery addresses by some couriers. All export orders must be placed and paid for online. Proforma Bank Transfer IBAN and SWIFT payment methods are available to create online.

Also Bought

Durite Standard Blade Fuse Holders (Interlocking) | Re: 0-376-00

Durite standard interlocking blade fuse holders with 6.3mm blade terminals. Can be clipped together to make a multiple fuse block.

Re: 0-376-00 
£13.16
Excl VAT
Available
0-601-03 Panel Mounted Cigarette Lighter Sized Power Socket

Durite 12 Volts 15 Amps panel mounted power socket, supplied with 100mm flying lead, rated 15A maximum at 12Vdc.

Re: 0-601-03 
£9.31
Excl VAT
Available
0-601-09 Cigarette Lighter Power Socket with Cover

Cigarette lighter power socket with cover for 28mm panel hole, supplied with removable (push type) cigarette lighter element.

Re: 0-601-09 
£10.17
Excl VAT
Available

Customer Feedback (0)
Leave a Review