0-776-00 Durite 7-inch 1080p AHD Camera System with 2 camera inputs and includes 1 x 1080p CMOS camera for vehicles.
- 7-inch colour TFT-LCD AHD display with parking guidelines.
- Supports up to 2 cameras.
- Supplied with remote control and 20m cable.
- Camera waterproof to IP68.
- Suitable for both 12/24V vehicles.
- E-Marked, R10 EMC, CE and UKCA approved.
Durite Colour I/R Waterproof Single-Wire Camera
The camera has a CMOS image sensor, which gives a high-quality picture, and its solid-state circuitry provides an extremely long life. The compact size and single connection make it easy to install. Automatic gain control (AGC) provides a clear image in both strong sunlight and low light conditions and if lighting conditions fall below a set level, the Infrared LEDs will illuminate; note the image will be monochrome when using IR illumination. It is recommended that all camera lead connections are additionally sealed by either wrapping with a suitable tape or applying heat shrink sleeving, 19mm ID, over the joint of the connector. Connecting the system and testing it before fixing it is recommended to ensure the correct field of view is displayed. Drill a 20mm hole for the cable entry and fit the grommet to the through body hole. If fitting to an isolated return vehicle chassis, the camera bracket should be isolated from the chassis.
Specifications
Pick up element | 1/3 inch CMOS image sensor |
Sensitivity | 1 lux @ F2.0 / 0 Lux with IR on |
S/N ratio | 48 dB |
Electronic shutter | Auto |
Lens | f 3.68mm |
Video output | 1 Vpp, 75 Omega; |
AGC | Auto |
Power supply | 12-volt dc |
Power consumption | 50mA / 210mA IR on |
Weight | 450 g |
Dimensions | l 84 x w 79 x h 83mm |
Operating temperature | -40C to +85C |
Protection | IP68 |
Monitor Controls and Inputs
When the unit is first connected to a power supply, it automatically displays the last selected AV input. Pressing the POWER button will switch the monitor to standby, and the unit will remain on standby until switched on by either the POWER switch or the reverse gear switch. 1. POWER Button - Pushing the POWER button switches the unit between standby mode and on, where it displays the last selected AV input. The monitor will automatically power up and display AV2 (black) in mirror image mode when the reverse gear switch is connected and the reverse gear is selected. 4. MENU Button - Pushing the MENU button cycles through the on-screen menu: Volume, Mute, Contrast, Brightness, Colour and Mirror. The on-screen menu will automatically switch off after 5 seconds if no further buttons are pressed. The Mirror ON selection will cause both AV inputs to be displayed in the mirror image. The AV2 input will always display in the mirror image when it is triggered by the reverse gear switch, regardless of the Mirror selection. 5. UP/DOWN Buttons - Pushing the UP/DOWN Button adjusts the setting from 0 to 100 of the selected onscreen mode. With the on-screen menu unselected, the arrow buttons cycle between AV1(red) and AV2 (black). There may be a small delay of up to 2 sec before the new image appears. Note: Please remove the LCD screen protective plastic cover before use.
Monitor Connections
1. AV1/AV2 Camera Picture Signal Input - One or both of the camera input connectors can be used to connect to the cameras. (DC power supply to the cameras is fed through these connectors). AV2 (black) should be used for the priority reverse camera.
2. DC 12 -24 Volt Power Supply Leads - Ensure the wires are connected correctly to prevent damage. Connect the red wire with the fuse holder to an ignition-switched positive feed, the white wire to the reverse gear switch (+ve) and the black wire to the vehicle chassis ground (negative earth systems only). Note: The monitor can be supported by or suspended by the mounting bracket to allow various installation locations within the vehicle
Specifications
Display Screen Size | 126.5 x 100mm |
Power Source | DC 12-24 volt |
Power Consumption | . 8 watt |
Pixels Number | 960 x 234 |
System | NTSC/PAL (auto switch) |
Operating Conditions Temperature | 0C to +60C |
Storage Temperature | . -25C to +80C |
Humidity | Rh 90% |
Dimensions | 155 x 123 x 23mm |
Weight (gross) | 380g |
Dimensions | l 84 x w 79 x h 83mm |
Operating temperature | -40C to +85C |
Protection | IP68 |